I recently purchased a northstar 4000 psi pressure washer. I had the same series pressure washer for the past 6 years and used a downstream chemical unloader quick connect to pull chemical.

I attached it to the pressure washer and it is not pulling. I havent modified anything and I dont want to pull chemical through my machine. The injector might be worn out or have something inside of the valve causing it not to ****. If you are using a new high pressure hose or a longer hose this may also have an effect over the injector not working. Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine.

I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer.

Jan 19, 2008 - Pre-wash stages, Washing, Drying, Clay & 'Quick Detailing' Sponsored by Ultimate Finish. Suppliers of high quality detailing products including. Jun 14, 2016 - Compact pressure washer, plugs into hose, perfect for domestic use. £25 delivered.

My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine?

If necessary, are there adapter plates that can be purchase. Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely.

The oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any.

I will There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing.

Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch.and nothing.I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.

Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. Obrazec akta spisaniya sportivnogo inventarya.

No resistance = open ignit. Turn water on then actuate wand trigger.

Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval.

I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. This pressure washer is approx 18 months old! You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet.

These can be caused because the spill valve (pressure control valve) is stuck. When this valve s.

Deville Excel Model # EXHA2425 Pressure washer I have a deville excel Model # EXHA2425 pressure washer. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get pressure.

Someone on hear had told me it was a 'bypass valve sticki You 015 012need toput antifreeze in the out/outlet or/oil then start it up you are driing out the seals allways put away with repeating this step. My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops.

This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u. I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure.

But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller Sounds like the valve in the handle is sticking closed.